|
|
Post by ikabod on Mar 15, 2006 11:38:52 GMT 8
dati gamit ko rin nail cutter, put later found out mas ok yung nail nipper, that's more likely a miniturized na side cutter. hanap ka lang talaga nung flat yung blades, meron kasi medyo angled. ;D at with a cheap price of 100 or less, you can just get a new one kung mapurol na, or pahasa mo dun sa naglalakd na mang hahasa. although medyo ma question lang ang pagka macho mo nun. hehehehe  |
|
|
|
Post by r2d2t2 on Mar 15, 2006 13:15:26 GMT 8
ikabod, kulit nung hirit mo ha. its nice to have a funny man on board 
|
|
|
|
Post by ikabod on Mar 15, 2006 14:56:22 GMT 8
r2d2t2sir it's just based on real experience po. kahit nga nung nag hahanap ako sa shop ng bueaty products looking fo a good set of nippers, wala akong mahanap na flat, so i asked pa sa sales lady, aba ang bruha tinataasan ako ng kilas at tiningnan ng medyo kakaiba. sabi ko na lang for my sister. . .
|
|
|
|
Post by V2 on Mar 15, 2006 16:32:04 GMT 8
nippers is a snapper's best friend.
|
|
|
|
Post by ikabod on Mar 15, 2006 16:38:25 GMT 8
V2yup! i second that, pero kung makalyo na rin daliri nyo eh, you can use yung small scissors ng victorinox swiss knife na maliit, and tibay, kaya lang masakit kasi liit lang handle eh, pero clean cut rin sya at matagal mapurol. . .
|
|
|
|
Post by no3Ljm on Jun 6, 2006 0:54:27 GMT 8
hi ulit mga bros. it's 1240am na... gising pa rin ako...
medyo bored at wala sa mood kaya post-post lang muna ako dito...
sana ok lang... 
nweiz, on to the topic of side cutters...
i use the cutter from Bandai. bought it around P350 or P400 ata. can't remember... ;D
hmmm... there's Bandai again... i think all the people at Bandai is sure is RICH.
after you cut the sprues, do you sand it pa? i tried using those emery boards from watsons.
ok naman ang outcome.  cheap pa at P29.75 per packs.
|
|
|
|
Post by V2 on Jun 6, 2006 1:00:40 GMT 8
cutters then nippers then scrape off the excess plastic.
|
|
|
|
Post by xentar on Jun 6, 2006 8:27:19 GMT 8
same here.... for me its the Bandai cutters pa din for Gundam kits...... |
|
|
|
Post by ikabod on Jun 6, 2006 9:52:57 GMT 8
yup tried that bandai side cutters, it's pretty good, although medyo madali rin mapuro. and it's a little bit pricey if you buy them ulit agad. so like sir v2, use a nipper, which is cheaper so pwede kang bili ng bili para sa laigng matalas, sa pag trim mo. then for me i used a scalpel for the final retouch. hhmm come to think of it, better get a new side cutter at baka maubusan pa ng stcok sa sm tk. . . |
|
|
|
Post by christine_03 on Jun 21, 2006 3:56:25 GMT 8
yup tried that bandai side cutters, it's pretty good, although medyo madali rin mapuro. and it's a little bit pricey if you buy them ulit agad. so like sir v2, use a nipper, which is cheaper so pwede kang bili ng bili para sa laigng matalas, sa pag trim mo. then for me i used a scalpel for the final retouch. hhmm come to think of it, better get a new side cutter at baka maubusan pa ng stcok sa sm tk. . . ey guys san ba may nipper na hindi angled? ung flat? i tried every girly store in malls and wala akong makita? any store na meron in particular? or cheap model kit plastic cutters? pa pm ng mga price nila. thanks and loc din pala. ;D |
|
|
|
Post by ikabod on Jun 21, 2006 10:42:19 GMT 8
@snap
paano bang angle sinasabi mo? mismong yung blade nya? or oientation lang ng cutter? try looking for manicure sets, usually flat kasama dun kasi yun yung as in generics eh, plus you get a pusher (which pwede mong pahasa kay manong para tumalas and act like an xacto) and some files. me lalagyan pa. . .
|
|
|
|
Post by xentar on Jun 21, 2006 10:58:57 GMT 8
i think he was refering to the nipper with the curvy ends (cutting end)....... bro, there are lots of nipper with straight ends, just try to look around in other malls...... |
|
|
|
Post by ikabod on Jun 21, 2006 11:18:14 GMT 8
ah ok curve ends. iba nga yan, and check mo rin if talagang flat yung blade like the side cutters, malimit kasi eh medyo 'angle' yung blade, kung baga nakapalabas, hindi sya flat, kasi that's much safer to use for nails talaga. |
|
|
|
Post by christine_03 on Jun 22, 2006 1:13:08 GMT 8
@ ikabod and xentar. thanks sa info. siguro magpapabili na lang ako sa friend kong babae. medyo tinataasan ka nga ng kilay pag nagtatanong ka. and may tawag silang term for the flat nipper. it would be better talaga na maghanap ng taong alam ang tools niya. well thanks. info na lang ulit kung may makakita ng good cutting tools dyan
|
|
|
|
Post by ikabod on Jun 22, 2006 9:14:38 GMT 8
sige tita let us know ha? ahahahay. . . . ;D
|
|
cheap pa at P29.75 per packs.
keeping the site active as a place to dump info for easier backtracking.